This is latest KaeilOS / OpenEmbedded build test with Stamp9g20evb board by taskit
BUILD
Website : http://www.kaeilos.com
Build system : KaeilOS/OE 13-JUL-2009
Branch : org.openembedded.dev <-- do not use stable !
Machine : stamp9g20evb
Image : console-image
Command : MACHINE="stamp9g20evb" bitbake console-image
SHA-1 tag : 34b2c6d58596767386c3fde6e62151b026f1a103
Boot log
RomBOOT
U-Boot 2009.03 (Jun 16 2009 - 14:42:35) DRAM: 64 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: macb0
macb0: Starting autonegotiation...
macb0: Autonegotiation complete
macb0: link up, 100Mbps full-duplex (lpa: 0x45e1)
Hit any key to stop autoboot:
U-Boot> run kaeilos
macb0: link up, 100Mbps full-duplex (lpa: 0x45e1)
Using macb0 device
TFTP from server 192.168.0.251; our IP address is 192.168.0.184
Filename 'stamp9g20evb/uImage-2.6.29-r7-stamp9g20evb.bin'.
Load address: 0x22000000
Loading: ###################################
done
Bytes transferred = 1458796 (16426c hex)
## Booting kernel from Legacy Image at 22000000 ...
Image Name: KaeilOS/2.6.29/stamp9g20evb
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1458732 Bytes = 1.4 MB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux..................................................... done, booting the kernel.
Linux version 2.6.29 (koan@quad) (gcc version 4.2.4) #1 PREEMPT Sun Jul 12 21:12:46 CEST 2009
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: tastit Stamp9G20
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 396 MHz, master 132 MHz, main 18.432 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 mem=64M mtdparts=atmel_nand:128k(bootstrap)ro,
256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root) rw root=/dev/mmcblk0p1 rootdelay=1
AT91: 96 gpio irqs in 3 banks
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61804KB available (2756K code, 189K data, 108K init)
Calibrating delay loop... 197.83 BogoMIPS (lpj=989184)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 296 bytes
NET: Registered protocol family 16
AT91: Power Management (with slow clock mode)
AT91: Starting after user reset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 120
io scheduler noop registered
io scheduler anticipatory registered (default)
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
eth0 (macb): not using net_device_ops yet
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffc4000 irq 21 (00:50:c2:94:92:4e)
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00, irq=-1)
Driver 'sd' needs updating - please use bus_type methods
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xa1 (Micron NAND 128MiB 1,8V 8-bit)
Scanning device for bad blocks
6 cmdlinepart partitions found on MTD device atmel_nand
Creating 6 MTD partitions on "atmel_nand":
0x000000000000-0x000000020000 : "bootstrap"
0x000000020000-0x000000060000 : "uboot"
0x000000060000-0x000000080000 : "env1"
0x000000080000-0x0000000a0000 : "env2"
0x0000000a0000-0x0000002a0000 : "linux"
0x0000002a0000-0x000008000000 : "root"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 20, io mem 0x00500000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: at91_udc version 3 May 2006
mice: PS/2 mouse device common for all mice
rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
IRQ 1/rtc0: IRQF_DISABLED is not guaranteed on shared IRQs
Driver for 1-wire Dallas network protocol.
at91_mci at91_mci: 4 wire bus mode not supported - using 1 wire
Registered led device: D8:red
Registered led device: D9:yellow
Registered led device: D10:green
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-at91sam9 at91_rtt.0: setting system clock to 2009-07-12 22:01:10 UTC (1247436070)
Waiting 1sec before mounting root device...
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 USD 1.85 GiB
mmcblk0: p1
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 179:1.
Freeing init memory: 108K
INIT: version 2.86 booting
Please wait: booting...
mount: mounting sysfs on /sys failed: Device or resource busy
Remounting root file system...
root: mount: mounting rootfs on / failed: No such file or directory
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... udhcpc (v1.13.2) started
Sending discover...
eth0: link up (100/Full)
Sending discover...
Sending select for 192.168.0.228...
Lease of 192.168.0.228 obtained, lease time 600
adding dns 151.99.125.1
adding dns 151.99.0.100
adding dns 208.67.222.222
done.
Starting to configure packages...
Nothing to be done
Finished to configure packages.
INIT: Entering runlevel: 5
Starting Dropbear SSH server: dropbear.
Starting syslogd/klogd: done
## ## ### ######## #### ## ####### ######
## ## ## ## ## ## ## ## ## ## ##
## ## ## ## ## ## ## ## ## ##
##### ## ## ###### ## ## ## ## ######
## ## ######### ## ## ## ## ## ##
## ## ## ## ## ## ## ## ## ## ##
## ## ## ## ######## #### ######## ####### ######(R)
KaeilOS Linux stamp9g20evb ttyS0
KaeilOS 2008.1-test-20081222 stamp9g20evb ttyS0
KaeilOS 2009.1-test-20090712 stamp9g20evb ttyS0
stamp9g20evb login:
